PUSHLOC FITTING STAINLESS STEEL – 1/8" NPT TO 1/4" PTC TEE
Part # TS-0550-3055
Features
1/8NPT Male Fittings
Suits 1/4″ / 6mm Tubing
Stainless Steel Construction
Hi-Temp Viton O-Rings
WARNING - Proposition 65 Compliance Statement:
It is the responsibility of Turbosmart to warn its customers and employees that some products sold on this website contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
Important Emissions Note:
This product does not have a CARB EO #; it is not legal for sale or use in CA on pollution controlled motor vehicles. This is intended as a "Race Only" product to be used solely for competition. It's use is limited to closed-course and open-course racing that is formally sanctioned by a recognized racing organization; any other use including recreational off-road use, may be a violation of local, state and federal laws. It is the buyer's responsibility to verify legal use of this product for the intended application and use.
| Item# | Description | Qty. | Price | |
|---|---|---|---|---|
| TS-0550-3055 | 1/8" NPT to TEE 1/4" pushloc stainless steel | $36.89 |
IWG75 Wastegate Actuator Suit K04 Leon 5psi – Black
(0 reviews) Share it View Details
Turbosmart Upgraded Wastegate Actuators have been developed to provide the maximum possible boost response for your factory frame turbocharger. The Turbosmart IWG75 Series of upgraded Actuators benefit from an increased ‘Working Ratio’ over the factory equipment resulting in improved boost response, throughout the RPM range.
This Improved ‘working ratio’ is achieved through an increase to the effective surface area of the diaphragm and revisions to the actual springs fitted resulting in greater leverage of the forces the actuator is working against (boost and backpressure) while still being super-responsive.
Upgrading with the same base pressure as the factory, you can expect a broader boost and torque curve through peak boost being achieved earlier in the RPM and being held longer, into higher RPM. These improvements can be amplified with higher base pressures, however tuning and recalibration are likely required.
Gen4 HP Spring (30 PSI) Outer (Brown/Red) Suit WG38/40/45/50L
(0 reviews) Share it View Details
Turbosmart’s WG38/40/45 HP 30 PSI Outer Spring Brown/Red is a must-have for external wastegate setups. This spring provides the ideal boost pressure for any turbocharger, ensuring consistent and reliable performance even under extreme conditions. Turbosmart’s design ensures that this spring will last for years, providing maximum performance with minimal maintenance. With Turbosmart’s WG38/40/45 HP 30 PSI Outer Spring Brown/Red, you can trust that your engine will perform as expected every time you hit the gas pedal. Ensure your setup is up to spec with Turbosmart’s best-in-class external wastegate spring.
Precision Cast PT7675 HP-COVER Turbocharger 1150 HP
(0 reviews) Share it View Details
Purpose built with the LS-enthusiast in mind, this unit features a 360* hydrodynamic bearing system for exceptional reliability and increased thrust capacity. The turbocharger is available with (2) different turbine housing A/R ratios (T4 .81 A/R and T4 .96 A/R), making it ideally suited for a single or twin turbo application. Both options feature a 3 5/8” v-band discharge for easy downpipe installation. Additionally, the LS-Series PT7675 turbocharger comes standard with our ported H cover (4" inlet and 3" outlet) to protect against compressor surge. • LS-Series PT7675 w/T4 undivided .81 A/R (Turbocharger part number 02207012219)
PRECISION LS PT8284 PROMOD-COVER TURBOCHARGER 1350HP
(0 reviews) Share it View Details
Purpose built with the LS-enthusiast in mind, the turbocharger is available with (3) different turbine housing offerings: T4 .96 A/R, T5 .96 A/R, and T5 1.08 A/R. Making it ideally suited for a single or twin turbo application. Both options feature a v-band discharge for easy down-pipe installation. The T4 has a 4" turbine housing discharge, and the T5 has a 5" turbine housing discharge. Additionally, the LS-Series PT8284 turbocharger comes standard with our Pro Mod cover, 5" inlet and 4.2" V-Band outlet. LS-Series PT8284 w/T4 undivided .96 A/R (Part Number: 12416218359) LS-Series PT8284 w/T5 undivided .96 A/R (Part Number: 12416218399) LS-Series PT8284 w/T5 undivided 1.08 A/R (Part Number: 12416218419) Rated to support 1,350HP
There are no related products available.
join our email list
You’ll be first to know about Treadstone Performance Engineering new products, discounts and special events!
Be the first to add a review for this product
Review Product