IWG75 (TWIN PORT)WASTEGATE ACTUATOR SUIT BORG WARNER EFR B2 SINGLE/TWIN SCROLL 14PSI
Part # TS-0620-3143
Turbosmart Upgraded Wastegate Actuators have been developed to provide the maximum possible boost response for your factory frame turbocharger. The Turbosmart IWG75 Series of upgraded Actuators benefit from an increased ‘Working Ratio’ over the factory equipment resulting in improved boost response throughout the RPM range.
This Improved ‘working ratio’ is achieved through an increase to the effective surface area of the diaphragm & revisions to the actual springs fitted, resulting in greater leverage of the forces the actuator is working against (boost and backpressure) while still being super-responsive.
Upgrading with the same base pressure as the factory, you can expect a broader boost & torque curve through peak boost being achieved earlier in the RPM and being held longer into higher RPM. These improvements can be amplified with higher base pressures, however, tuning & recalibration is likely required.
Twin Port Actuators allow for a wider tuning window by plumbing a reference signal on either side of the diaphragm. The boost control strategy can force the pressure into the top cap for a higher ‘high boost’ target and, equally, force pressure under the diaphragm for a lower ‘low boost’ target. Twin Port Control allows greater boost control options around the base spring pressure. Often a much softer spring than usual can be used, resulting in an overall improvement in dynamics and response.
Features
Proprietary Silicon Nomex Diaphragm
Choice of Springs from 3psi to 26psi (Optional)
High-Grade Billet Aluminum Construction
Stainless Steel Rods and Clevis
Turbosmart Unique Locking Collar System
It is the responsibility of Turbosmart to warn its customers and employees that some products sold on this website contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
This product does not have a CARB EO #; it is not legal for sale or use in CA on pollution controlled motor vehicles. This is intended as a "Race Only" product to be used solely for competition. It's use is limited to closed-course and open-course racing that is formally sanctioned by a recognized racing organization; any other use including recreational off-road use, may be a violation of local, state and federal laws. It is the buyer's responsibility to verify legal use of this product for the intended application and use.
Tell Us How You Feel!
| Item# | Description | Qty. | Price | |
|---|---|---|---|---|
| TS-0620-3143 |
IWG75 Borg Warner EFR Twin Port B2 Single and Twin Scroll 160mm Rod Black - 14psi
ADD TO CART
|
$247.49 |
ADD TO CART
|
Precision GEN2 PT11814 PROMOD-COVER TURBOCHARGERS 2800 HP
(0 reviews) Share it View Details
PTE's GEN2 PT118 CEA® Turbocharger features the following: Exclusive CEA® (Competition Engineered Aerodynamics) compressor wheel machined from a 2618-aluminum forging Higher efficiency and faster transient response for maximum power and performance 118mm inducer compressor wheel Large frame compressor cover with a smooth, 7" radiused inlet H-trim turbine wheel Customers can choose an undivided T5 turbine housing in either 1.50 A/R or 2.0 A/R
Tell Us How You Feel!
Precision GEN2 110114 PROMOD-COVER TURBOCHARGERS 2900 HP
(0 reviews) Share it View Details
PTE's PT110 Turbocharger features the following: HP Rating: 2500 110mm inducer compressor wheel Large frame compressor cover with a smooth, 7" radiused inlet G trim turbine wheel Turbine housing options: - T5 Tangential 1.0, 1.32, or 1.50 A/R with 5" OD (outer diameter) V-band discharge Hydrodynamic 360 thrust bearing system
Tell Us How You Feel!
Precision NEXT GEN PT6875 SPORTSMAN-COVER TURBOCHARGER 1200 HP
(0 reviews) Share it View Details
NEXT GEN 68mm CEA (Competition Engineered Aerodynamics) compressor wheel machined from a 2618-aluminum forging. Air-cooled, Dual Ceramic Ball-Bearing Center Housing Rotating Assembly (CHRA) Sportsman compressor cover with a 5.0” inlet and 4.2” outlet 75mm CEA turbine wheel Air-cooled, dual ceramic ball bearing Turbine housing options: T4 divided inlet with .98 A/R, 1.12 A/R, or 1.28 A/R and 4 5/8” OD v-band discharge. Also available in a stainless steel v-band inlet/v-band outlet configuration for a $206.00 upcharge. Available A/R ratios are 1.00, 1.15, and 1.28 Rated to support 1,200 flywheel horsepower.
Tell Us How You Feel!
Precision NEXT GEN PT7685 SPORTSMAN-COVER TURBOCHARGER 1500 HP
(0 reviews) Share it View Details
All new sportsman frame sized 7685 turbocharger features a NEXT GEN, 76mm CEA compressor wheel mated to our 85mm high flow turbine wheel. This unit is based on the Sportsman ball bearing turbo and is available with multiple turbine housing options. Designed to take your build to the NEXT GENERATION, the NEXT GEN Sportsman 7685 is a record setting turbocharger and is a great option for those looking to make upwards of 1,500hp. NEXT GEN 76mm CEA (Competition Engineered Aerodynamics) compressor wheel machined from a 2618-aluminum forging. Air-cooled, Dual Ceramic Ball-Bearing Center Housing Rotating Assembly (CHRA) Sportsman compressor cover with a 5.0” inlet and 4.2” outlet 85mm CEA turbine wheel (85mm Exducer / 90mm Inducer) Air-cooled, dual ceramic ball bearing Turbine housing options: T4 divided inlet with .98 A/R, 1.12 A/R, or 1.28 A/R and 4 5/8” OD v-band discharge. Also available in a stainless steel v-band inlet/v-band outlet configuration for a $206.00 upcharge. Available A/R ratios are 1.00, 1.15, and 1.28 Rated to support 1,500 flywheel horsepower.
Tell Us How You Feel!
There are no related products available.
join our email list
You’ll be first to know about Treadstone Performance Engineering new products, discounts and special events!
Be the first to add a review for this product
Review Product